Part Two. Revit

Chapter 11. Add/edit beams, walls, & curtain walls

Session Objectives

Upon completing this session, students will be able to:

  • (CO 1) Add/Edit Beam
  • (CO 2) Create walls
  • (CO 3) Edit walls wall properties – Wall thickness, Wall details, & Finishes
  • (CO 4) Edit/add wall properties – Wall opening, wall sweep
  • (CO 5) Add/Edit Curtainwalls, Mullions, & Panels

 Session Highlights

At the end of the session, students can create the graphics below.

It shows the session highlight presenting beams, walls, and curtain walls. This is the expected result at the end of this lecture.


 Lecture Contents

(CO 1) Add/Edit Beam

Adding beams are not typical for interior design projects, but it is needed for the Eames House project. You may use this information for an open ceiling plan of commercial projects as well.

You can find [BEAM] from the [STRUCTURE] tab, under the [STRUCTURE] panel.
It shows the structural tab and the Beam tool.

If you are missing the Structure tab, click [HOME] menu > Click [OPTION] > Click [USER INTERFACE] > Check [STRUCTURE TABL AND TOOLS]
It indicates how to open the structural tab if you don't have one.

To see the structural element in solid shapes instead of lines, the view detail level must be [FINE]. Please update all floor plans, ceiling plans, and elevations to [FINE] on a detail level.
It indicates how to change the detail level to Fine.

Add Beams

  • [STEP 1] Click [Beam] on [Structure]
  • [STEP 2] Select W Shapes-W5X5
    • If you don’t have a W5x5 type. Please add one by clicking Edit Type > Duplicate > Name the type > Edit Width and Height to 5
  • [STEP 3] Select [Level: Level 2] from Option Bar [Modify/Place Beam] for the West Wall of the building
  • [STEP 4] Click the center of the north column of the west wall, and click the center of the south column of the west wall. You will get a warning message, but it is OK, just click X
    It shows what type of beam is using and the placement on the plan.
  • [STEP 5] Confirm the place from the 3D view by clicking the HOUSE icon from quick access and hide site information by category. Update the 3D view scale to 3/8”=1’-0.”
    It indicates how to open 3D view to confirm the beam placement is right.
  • [STEP 6] Open the 3D view, West elevation, and the floor plan together by typing [WT]
    It indicates how to see both the 3D view and floor plan together to confirm the right placement.
  • [STEP 7] The Beam must be rotated to 90 degrees.
    • Click the Beam, and change the properties
    • Change Cross-Section Rotation to 90 degree
    • The beam location needs to be aligned from the Top view of the 3D view. Use Move (MV) command to move the Beam to be aligned.
      It indicates how to rotate the beam and move the beam to be aligned.
  • [STEP 8] See the West elevation and move the Beam to align with the imported image, [MOVE] command will not work.
    • Thus, update [Y OFFSET VALUE] to [1’ 1 ½”]
      It indicates how to move the beam to align with the imported drawing.
  • [STEP 9] For other beams repeat step 1 through step 8. You may select all beams that you created and change the properties – Step 6 & 7. or Copy elements that have the same properties.
    • Complete beams for the second floor and the roof exterior beams, AND the second level interior beams
      It shows the resulting image after completing the placement of 5x5 beams.

Add NEW Beams from a new family

  • [STEP 1] Click [Load Family] on [Insert] tab
  • [STEP 2] Download [LH-Series Bar Joist.rfa] from Canvas Eames House module
  • [STEP 3] Find the folder and select the file and Open
  • [STEP 4] On Roof plan, Click [BEAM] on the [STRUCTURE] tab
  • [STEP 5] Click North column and South column to create the Bar Joist
    It indicates how to add new beam.
  • [STEP 6] Edit the family type to match the imported drawing
    It indicates what to edit for the new beam.
  • [STEP 7] Copy (CO) the first Bar Joist for the other Bar joists
    It shows the resulting image after completing the new beam.

(CO 2) Create walls

Draw WALLs with Various types based on the imported base drawing image

  • [STEP 1] Select [WALL] from [ARCHITECTURE] tab, under [BUILD] panel
    or Type [WA]
  • [STEP 2] Select a Wall family
    • If you don’t have a wall type from the Properties, add by clicking Edit Type and Duplicate from a wall type.
    • For Eames House, we will use
      • Curtain Wall 1
      • Retaining -12” Concrete
      • Interior-4 7/8” Partition
      • Interior-6 1/8” Partition
      • Soffit-1/2” GWB & Metal Stud
    • But the wall details will be modified, and custom walls will be added later in this tutorial.
  • [STEP 3] Confirm [BASE CONSTRAINT] and [TOP CONSTANINT]. If needed set base offset and top offset
  • [STEP 4] Specify Location Line
  • [STEP 5] If the wall is other than a straight line, specify a line/shape type (circle, arc, rectangle, inscribed polygon, or ellipse. And draw lines to cross-reference of the imported base drawing image
  • [STEP 6] Make Dimensions [DI] for verification purposes.
  • [STEP 7] Confirm with 3D view
    It shows the resulting image after drawing the walls.

(CO 3) Edit walls wall properties – Wall thickness, Wall details, & Finishes

For your wall thickness, refer to Kilmer, W., & Kilmer, Rosemary. (2016). Construction drawings and details / W. Otie Kilmer and Rosemary Kilmer. (Third ed.).

For your design project, you will need to decide on your construction details.

Typical residential house wall thickness (For your reference)

  • Interior Wall (without Plumbing) = 4 ½” ((1) 2”X4” wood stud, which are 3 ½” deep + (2) ½” Gypsum boards)
  • Interior Wall (with Plumbing) = 6 ½” ((1) 2”X6” wood stud, which are 5 ½” deep + (2) ½” Gypsum boards)
  • Exterior Wall (with Brick) =  10” ((1) 2”X6” wood stud, which are 5 ½” deep + (1) ½” Gypsum boards + (1) ½” Insulation + (1) 3 ½” Brick)
  • Exterior Wall (with Stucco, wood, aluminum, or vinyl) = 7 1/2”  ((1) 2”X6” wood stud, which are 5 ½” deep + (1) ½” Gypsum boards + (1) ½” Insulation + (1) 1” Stucco, wood, aluminum, or vinyl)

For the Eames house project, although this building is residential, the construction is a combination of wood base and metal base. Revit provides walls for commercial construction, which is a metal base, so, you may use the provided walls and change some walls.

  • Interior Wall = Wood stud with Gypsum BD + Paint Finish or Wood BD (3 1/8”, 4 7/8”, 6”, 8”)
  • Exterior Wall = Curtain Wall with Glass, Wood, Metal panels
  • Exterior Wall = Metal with Gypsum BD + Paint Finish or Wood BD
  • Exterior Retain Wall = Concert

Once you click a wall, you can edit the properties (wall height-where it starts and ends & wall phase) for each wall

If you want to change the wall’s type (wall thickness Graphic style, materials, Structure, BIM information), you can change by clicking [Edit Type]

For the future strategy, it is wise to [Duplicate] the type and edit type properties. For best practice, add “000” for the new duplication. This will allow the types to organize in alphabetical order.
It indicates how to edit the Wall type.

Click [EDIT] on [STRUCTURE] and change thickness and material and click [OK]
It indicates how to edit wall assembly.

To change other walls from the Revit Metal base 4 7/8” wall to Wood base 4 ½.”

  • [STEP 1] Click one of Metal base 4 7/8” wall
  • [STEP 2] Mouse right click and click [Select all instances] and click [in Entire Project]
  • [STEP 3] Select [000_Interior-4 ½” Partition]
    It indicates what to edit the Wall type.

(CO 4) Edit/add wall properties – Wall opening, wall sweep

Wall opening or wall elevation modification

  • [STEP 1] On a plan view, click the wall that you want to make wall opening
  • [STEP 2] Click [Edit Profile]
    It indicates how to edit wall profile.
  • [STEP 3] Go To View window will open.
  • [STEP 4] Select an appropriate view to open. I prefer the ISO view to quickly change the elements
    It indicates how to edit wall profile.
  • [STEP 5] Draw the opening with dimension
  • [STEP 6] Click the green checkmark to finish
    It indicates how to edit a wall profile.
  • [STEP 7] Double check in 3D view

Wall Sweep is a very useful tool to create moldings

  • [STEP 1] To create a continuous molding. First, you need to load a profile by clicking [Load Family] from the [Insert] tab.
  • [STEP 2] Find Profile from Revit library and open it to the file.
    It indicates that where to load the Wall profiles.
  • [STEP 3] Click the small arrow under Wall on Architecture tab
  • [STEP 4] Select Wall: Sweep on 3D view. Recommend a camera view or a 3D view with a section box
  • [STEP 5] Click [Edit Type] > Duplicate the type. Don’t forget to add “000” for your type.
  • [STEP 6] Click profile under construction, select the profile you just loaded.
    It indicates how to change the wall sweep profile.
  • [STEP 7] See the preview and click the appropriate location on the wall for the molding on the 3D view.
  • [STEP 8] To finish the Sweep, [ESC] on Keyboard.

(CO 5) Add/Edit Curtainwalls, Mullions, & Panels

Modify curtain wall

  • [STEP 1] To add curtain wall grids, open a view. It can be an elevation view. You may close the floor plans.
  • [STEP 2] For the Eames house project, confirm the imported base drawing – elevations are in the correct locations.
  • [STEP 3] Click [Curtain Grid] on [Architecture] tab
  • [STEP 4] Select [All Segments] or [One segment]
  • [STEP 5] Click grid lines and use dimensions for accurate distance based on the imported  elevations
    It indicates how to set curtainwall grids with dimensions.
  • [STEP 6] You can edit the grid, click the grid, and click add/remove segments.
    It shows the resulting image after creating curtainwall grids.
  • Complete for all four exterior walls

Add curtain wall mullion

  • [STEP 1] On the elevation, click [MULLION] on the [ARCHITECTURE] tab
  • [STEP 2] You may choose All Grid Lines, Grid Line, or Grid Line Segment
  • [STEP 3] Also, you may choose a specific type of Mullion by clicking Properties, and you can edit the type as well
    • You can change material, size, profile, the width of sides, angle, & offset
  • [STEP 4] Click lines to apply the mullion type that you selected
    It indicates how to apply mullions.

Modify Mullion

  • [STEP 1] If you need to change the mullion type, you can click the mullion that you made and change the properties
  • [STEP 2] If you need to change the mullion type and join order, click the Mullion you want to change and click [+] on the view to change the order
    It indicates how to modify mullion details.

To change the panel from Glazing to Solid, door, or window

  • [STEP 1] Select the panel to change by multiple [Tab] keys
  • [STEP 2] Change Properties to what you need
  • [STEP 3] If you need to change the properties, click [Edit type] and click [Duplicate] and change the value
  • [STEP 4] If you need to add a new type, Load family first and change the Properties
    It indicates how to apply panels.

SAVE the file before closing the application.

Save in a different location for the backup (e.g., a cloud folder)

License